CARLINKASCL6 Remote Start Cellular Interface Module Allows You to Start Your car from Your Phone 1 Year Included

I purchased a Start-X remote starter a week ago for my 2019 Toyota Corolla LE (key start). Installation was easy for that, but after using it a few days, i realized that i was parking a bit out of remote range depending on what time I made it to work. Also, if i was close, i had to goto the window and try to remote start it which was a pain. Needless to say I decided to add the cellular interface.My first thoughts about doing this was that it was going to be really hard. I didn't see any videos out there specific to my car and the instructions were a bit complicated, plus I did not see a Start-X starter listed in their instruction sheet. I pulled out the starter and noticed it was labelled CM-DC3, which seems to be a Compustar CM-DC3 type. I matched up the instructions to that particular unit, but was hesitant as I didn't want to plug in something and mess everything up entirely. I shouldn't have been hesitant as the entire setup process with testing took about 15 minutes. Shout out to reviewer Red as i was more confident after reading his review.So here is what I did:Prior to doing anything I downloaded the application and setup an account.- Note that you will be in a test/installer mode when you activate everything- Write down your password!! Reason below....Using only the long cable (did not need the small multi cable at all)- Plugged in the long cable to theASCL7 (they sent me the latest unit instead of the ASCL6, thank you!!!)- Plugged in the blue end to the grey telematics port on the Start-X- Waited about 30 seconds and then the unit started flashing.- I waited until all the lights were solid on the ASCL7- Added the unit by opening the app on my phone and scanned the serial number to add the unit; there are a few extra labels with the unit so keep them handy- It asked for the make/model/type of car it will be installed on as well as the VIN number to identify the vehicle so I entered that in as well- Once entered, it asked for the start type, i chose ADS protocol- The app stated that it was updating the protocol on the device for the car - took about 3-4 minutes to update and restart (see pictures)- Once finished and the lights were solid again, I put everything back in its place, shut the door and did a test. Doors unlocked and locked. Trunk popped open just like the remote. Start and stopping the engine worked perfectly. GPS was accurate.- Since it was in test mode, i released it. I then re-added the serial number back into the app and it picked it right up.So far so good. I will know better as time goes by and I am at work and need to park farther away.I do have one con at this time - no Apple Watch app. So when I originally placed the order, i had downloaded the CL6 application, and that also installed the app on my watch. When they sent the CL7 model, it directs you to use the CL7 app, however that does not have the watch application even though the pictures depict it. Not a big deal, but if i don't have to pull out my phone to start the car then that is a plus.Also, one other thing, write down your password, use a password manager, whatever. When I installed the CL7 app, i forgot the password to when i setup the CL6 app. If you try to do the 'reset password' option, it never sends the email. Checked junk folders, nothing. I had to sign back up again for the CL7 app.All in all, took me just under 15 minutes to add this to my Start-X controller.Another note, before i started I did email Start-X twice to see if they had any hints, tips, etc... never heard from them, which is kind of strange considering some of the reviews I read where they were quick to respond. Regardless, this worked well for me but all starters are different from my limited research.Hope this helps someone with a similar car/starter combination.***UPDATEWorking fine so far, no issues really, very reliable. Some post notes:- GPS is really accurate, withing a few feet. I placed the device inside the the dash behind the small drivers side panel.- The app showed 2 of the same car initially. It did not hinder anything. I emailed their support via the app. The duplicate disappeared prior to them getting back to me (was there for about 5 or 6 days). When they got back to me, they said they dont see the duplicate in the account. Been fine since.- The app also notifies you of any outages. I only had two notifications, one of which would not signal the car to start. Not a big deal as it was in my driveway at the time. The other notification that happened, the car started normally, so it may have been a region thing.- Start-X did email me back and confirmed how i set it up was correct.- No extra controls available, like rolling the windows down or up, only what is on there. Im sure it could be programmed somehow to do it, but its not something i need to get done.- No issues with countdown clock. Some videos I watched show it starting off at 35 minutes then dropping down to 15 minutes after a few seconds. I don't see that with my setup.- Comes with a free 30 day trial to the Premium Plus plan. It will notify you to try it out after the 1st day.- Apple Watch app still not present with the CL7 version.

Stay clear of this if you're trying to add it to a Evo remote start. I ordered this a while back ago because it showed compatability with the Evo. Upon further installation it says you have to buy the fortin flashlink to update it. I've tried I have talked to both Evo and carlink , carlink says it's a Evo problem and won't help, Evo has sent out a replacement and after doing as instructions read again and again The carlink will just start the car and it immediately shuts off. Thw app won't even show any information as to why it didn't work, the app even says if it doesn't start it'll show a fault but it doesn't After messing with this for months I'm cutting my losses and going to buy a Evo one. Which after further digging into this this carlink it's had multiple problems and even when you buy through Evo carlink is not one they show is compatible.

If the previous owner or user did not unregistered the device, carlink/voxx will not do anything for you. the seller/amazon must have the unit unregistered/released.update 9/18/24I purchased a new one and received a free upgrade to a CL7 unit. The setup was easy and simple, but as everyone says, instructions are trash.Here is my setup that works with full control.1. Create your account first. This is very important. With an account, you can set the protocol within the app's setup phase.2. connect the wiring harness blue clip to the other harness blue clip.3. don't worry about connecting the loose wires (you won't need them at all)4. connect the white connecter to the start-x module (although there are 4 connectors you want the white one it's the only one that will connect to the start-x module )5. when you connect the CL7 unit wait until the blue light becomes solid then follow the app instruction6. protocol: select "Directed"7. The unit will receive a download and then restart, wait until the blue LED turns solid.8. now test .9. when you are done testing, release the vehicle from testing mode .... you are now good to go.